Antimicrobial Interior Coating – MIG-ESP® Interior Anti-Microbial

• solvent-free, environmentally friendly and odorless
• water-repellent, microporous and non-film-forming
• highly permeable to water vapor (sd value 0.06 m± 0.02)
• Water absorption, w-value after 24 hours <0.50 kg/m2h0.5
• Wet abrasion class II
• Coverage class II at approx. 0.25 L/m²
• Whiteness: L>94.0
• Gloss level: matt (DIN 53778)
• Density 1.15 g/cm³ (± 0.1)
• Reflectance >90% with white coating
• Crack filling up to approx. 0.50 mm
• antibacterial effect (99.99% MRSA and Escherichia coli reduction)

1. Prepare the surface

The surface must be clean, dry, solid and free of efflorescence, dust and loose parts or release agents (e.g. formwork oil). Depending on the surface, apply MIG-ESP Sealing Primer as a plaster hardener - allow to set for approx. 1 hour. For tarpaulins, use MIG-ESP PVC Primer.

2. Apply primer

Depending on the substrate, apply MIG-ESP Sealing Primer as a plaster hardener - allow to set for approx. 1 hour. For tarpaulins, use MIG-ESP PVC Primer.

3. Stir

Mix MIG-ESP Interior Anti-Microbial with an electric mixer for approx. 3 minutes until the consistency is creamy.

4. First order

Distribute MIG-ESP Interior Anti-Microbial, White evenly in a criss-cross pattern and roll in one direction in the last application.

5. Drying time

24 hours drying time between both coating processes MIG-ESP Interior Anti-Microbial.

6. Second order

Spread the white or colored paint evenly in a criss-cross pattern and roll it off in one direction in the last step.

MIG-ESP® Interior Anti-Microbial dries quickly and is odorless during application, which also allows it to be used while the room is in use. Before application, the material must be stirred mechanically for approx. 3 minutes. Cover all adjacent components well and protect them against splashes.

Do not use in high relative humidity. MIG-ESP® Interior Anti-Microbial should be applied evenly using suitable rollers, brushes or the MIG-Zip 52 sprayer. The nozzle size should be 2.5 mm. The low-pressure MIG-Zip 52 sprayer with nozzle size 2.5 mm specified for the coating can be purchased from us. MIG-ESP® Interior Anti-Microbial must not be mixed with or diluted with other materials. The object and ambient temperature must not be below + 5°C or above + 35°C during application. Shading is necessary in the event of sunlight. Surface drying is achieved after just 30 minutes. The drying time for each of the two coating processes is approx. 24 hours under normal conditions (+ 20°C/65% relative humidity). Lower temperatures and higher relative humidity extend the drying time.

The substrate must be clean, dry, solid and free of efflorescence, dust and loose parts or release agents (e.g. formwork oil). For absorbent substrates and plasterboard, a primer coat with MIG-ESP Sealing Primer is required. This solidifies the substrate and evens out different absorption behavior. For metal, concrete and plaster surfaces as well as contaminated, penetrating substrates, we recommend MIG-ESP® Special Primer as a bonding bridge. For highly absorbent surfaces such as stucco, porous lightweight concrete, aerated concrete, mineral insulating plaster, foam concrete, foam glass, silicate and insulation boards, it is generally necessary to apply MIG-ESP® Sealing Primer twice. For tarpaulins, our MIG-ESP PVC Primer should be used.

►To achieve the full effectiveness of the MIG DHMb Lining technology, a dry layer thickness of 0.40 mm is required! If MIG-ESP Interior Anti-Microbial is applied with a roller or brush, experience has shown that two coating processes are necessary to achieve the required layer thickness. When processing colored MIG-ESP® Interior Anti-Microbial, MIG-ESP® Interior Anti-Microbial, white, should be used for the first coating process, and the second coating is then colored. Any construction defects or damage must be repaired before application!

consumption

Depending on the type and absorbency of the substrate, approx. 0.50 L/m² for two coats on smooth surfaces.

Rough, structured or highly absorbent surfaces can increase consumption considerably. Exact consumption quantities can be determined by creating test areas.

cleaning

Clean tools thoroughly with water after use. Empty containers completely and recycle them.

storage

Stored in a dry, frost-free and cool place under proper conditions in the original, sealed containers, the product can be stored for at least 12 months from the date of sale. Dyed goods must be processed within 3 months.

guarantee

We offer a 10-year quality guarantee on our MIG-ESP® Interior Anti-Microbial interior coating. This guarantee applies exclusively to the product applied to the surfaces by specialist companies and not to the associated services in compliance with our guarantee conditions. A complete chain of evidence of correct application must be provided.

Legal Notice

The information in this publication is based on our current technical knowledge and experience. Due to the multitude of possible influences when processing and using our products, it does not exempt the processor from carrying out their own tests and trials. They only represent general guidelines. A legally binding guarantee of certain properties or suitability for a specific application cannot be derived from this. Any protective rights as well as existing laws and regulations must always be observed by the processor at his own responsibility.